'Mike, I have the CD done with the crashed PT-19's from the 1940's. Send me
your address off line so I can mail it to you. I had about 12 to 15
pictures.
Jack
Jack Threadgill
1602 Brook Hollow Dr
Bryan, TX 77802
979-779-7155
threadgl@suddenlink.net
-----Original Message-----
From:
fairchildclub@yahoogroups.com [mailto:
fairchildclub@yahoogroups.com]
On Behalf Of Michael Denest
Sent: Thursday, May 29, 2008 7:18 PM
To:
fairchildclub@yahoogroups.com
Subject: Re: [fairchildclub] Bearings for PT-19/23/26
Hey! You weren't supposed to tell! Just kidding, it keeps him out of
trouble.
Mike
Quando omni flunkus moritati
(If all else fails, play dead)
- "Red" Green
----- Original Message ----
From: "pt19flyer@aol. com"
To: fairchildclub@ yahoogroups.com
Sent: Thursday, May 29, 2008 10:35:15 AM
Subject: Re: [fairchildclub] Bearings for PT-19/23/26
I just got off the phone with my secret source and he is sending me some
bearings.? Thanks for your assistance.
Richard
My Secret Source, as in the past is named Joe and lives in PA.? I bet you
know him too.
-----Original Message-----
From: Curt Kinchen
To: fairchildclub@ yahoogroups. com
Sent: Wed, 21 May 2008 3:26 pm
Subject: RE: [fairchildclub] Bearings for PT-19/23/26
Here's another one with some in stock....in Australia:)
http://nswbearings. com/
Curt Kinchenptcurt@ msn.com
To: fairchildclub@ yahoogroups. comFrom: pt19flyer@aol. comDate: Wed, 21 May
2008 15:01:01 -0400Subject: Re: [fairchildclub] Bearings for PT-19/23/26
Curt,We found some that are the same size OD and ID, but .25 width.? We
could use them if we had a spacer of come sort plus the paperwork to go
along with it.Any ideas?Richard- ----Original Message----- From: Curt
Kinchen To: fairchildclub@
yahoogroups. comSent: Wed, 21 May 2008 1:39 pmSubject: RE: [fairchildclub]
Bearings for PT-19/23/26On more careful examination what I said may not be
correct. The KP4A may only be .25" thick(accordingto the source website
info).Curt Kinchenptcurt@ msn.com To: fairchildclub@ yahoogroups. comFrom:
ptcurt@msn.comDate : Wed, 21 May 2008 11:33:34
-0700Subject: RE: [fairchildclub] Bearings for PT-19/23/26It would appear,
from the link below, that the obsolete part number KF4A would be replaced
with a KP4A. The difference being the seal type.http://
www.promshop.
info/cataloguesp df/form643. pdfHere's a source I found with a quick search.
http://www.machinem adness.com/ fafnir_bearings. htmCurt Kinchenptcurt@
msn.com To: fairchildclub@ yahoogroups. comFrom: pt19flyer@aol. comDate:
Wed, 21 May 2008 13:06:45 -0400Subject: [fairchildclub] Bearings for
PT-19/23/26Some one out there must have resolved this issue in the past, so
before searching the web, allow me to ask.There is a Fafner Bearing that is
used on the rudder (I think it is also used on the ailerons)The part number
appears to be KF4AThe dimensions are? .75" OD, .25" ID, .50" WidthIt is a
felt seal
ed ball bearing.I need about 8.Any source or replacement options.? If
replacement options, do we have the appropriate paperwork?Thanks, Richard
SmithAustin, Texas[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed] [Non-text portions of
this message have been removed][Non- text portions of this message have been
removed]
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]
[Non-text portions of this message have been removed]'