Fairchild Club Forum

'

> Hellå

I made my spacers of a steel tube fitting the bolt.
I also found that the yoke differs in dimension so again it is best to make them fit your 10´yoke. The bushings must also fit the seals you have and those differs to.
The 10´tail wheel was at the time a army speck, UC 61, so I don´t think there is a STC for it. John Berent has probably all the drawings.

paul

> Från: "m77mb"
> Datum: 2004/11/18 Thu AM 12:27:35 CET
> Till: fairchildclub@yahoogroups.com
> Ämne: [fairchildclub] tailwheel spacers for 10"SC tailwheel
>
>
>
> I need 2 spacers for the 10' sc TAILWHEEL. These fit outside the
> bearings between the tailwheel and the yoke. The axle slides through
> them. Does anyone know where I can get them? Also , even though I am
> attempting to put back the original style of tailwheel and tire ( I
> have a new tailwheel, tire and tube) there is a non-standard
> tailwheel already on the plane which has a 4" wheel and 2.8/2.5 x 4
> tire already. Can't find any STC for this conversion. Is there one?
> Thanks
> Donis B. Hamilton
> NC81311
> 1946 F24R-46
>
>
>
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>

-------------------------------------------------
WebMail från Tele2 http://www.tele2.se
-------------------------------------------------'

'Thanks for the word. Talked with John and he said the same thing. Got some tubing and made some . Came out O.K. Operates and flies great. Have some shimmy but not hard. It's relieved by forward pressure on the stick. Will have to get new tail wheel tire (ordered but not yet reciieved). That and thorough greasing of the tailwheel assembly may relieve the shimmy . Thanks again
Donis

paul.pinato@swipnet.se wrote:

> Hell?

I made my spacers of a steel tube fitting the bolt.
I also found that the yoke differs in dimension so again it is best to make them fit your 10?yoke. The bushings must also fit the seals you have and those differs to.
The 10?tail wheel was at the time a army speck, UC 61, so I don?t think there is a STC for it. John Berent has probably all the drawings.

paul

> Fr?n: "m77mb"
> Datum: 2004/11/18 Thu AM 12:27:35 CET
> Till: fairchildclub@yahoogroups.com
> ?mne: [fairchildclub] tailwheel spacers for 10"SC tailwheel
>
>
>
> I need 2 spacers for the 10' sc TAILWHEEL. These fit outside the
> bearings between the tailwheel and the yoke. The axle slides through
> them. Does anyone know where I can get them? Also , even though I am
> attempting to put back the original style of tailwheel and tire ( I
> have a new tailwheel, tire and tube) there is a non-standard
> tailwheel already on the plane which has a 4" wheel and 2.8/2.5 x 4
> tire already. Can't find any STC for this conversion. Is there one?
> Thanks
> Donis B. Hamilton
> NC81311
> 1946 F24R-46
>
>
>
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>

-------------------------------------------------
WebMail fr?n Tele2 http://www.tele2.se
-------------------------------------------------


Yahoo! Groups SponsorADVERTISEMENT


---------------------------------
Yahoo! Groups Links

To visit your group on the web, go to:
http://groups.yahoo.com/group/fairchildclub/

To unsubscribe from this group, send an email to:
fairchildclub-unsubscribe@yahoogroups.com

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.



---------------------------------
Do you Yahoo!?
Meet the all-new My Yahoo! ? Try it today!

[Non-text portions of this message have been removed]'