Page 1 of 1
F24 elevator control Rod End
Posted: Wed Jun 05, 2002 2:00 pm
by F.J. & D.A.Cox
'Folks,
My rear elevator control 'Rod End' has been condemned.
It is 7/16 inch male thread with a 3/4 inch ring and a Fafnir S1K-5 Bearing which has a 1/4 inch bore.
The problem is trying to match a 7/16 inch shaft with a 1/4 inch bore.
Does anybody have a seviceable one for sale or know where I could buy one or a modern equivalent?
I am also looking for Flat Head Machine screws with 82 degree countersink 1/4 X 1 1/8 and 1/4 X 1 3/8 All the usual sources do not stock them or the rod ends these days.
Thank you for any info.
Frank Cox
[Non-text portions of this message have been removed]'
Re: F24 elevator control Rod End
Posted: Wed Jun 05, 2002 4:48 pm
by JOHN
'Frank
I have some control rod ends that might work for you. Give me a few days and I will dig the box out and check for you. If I do you can have it just pay the postage.
John
----- Original Message -----
From: F.J. & D.A.Cox
To:
fairchildclub@yahoogroups.com
Cc:
JSTreat360@aol.com ;
wbaf1595@att.net ; Tracy's mail
Sent: Wednesday, June 05, 2002 3:08 PM
Subject: [fairchildclub] F24 elevator control Rod End
Folks,
My rear elevator control 'Rod End' has been condemned.
It is 7/16 inch male thread with a 3/4 inch ring and a Fafnir S1K-5 Bearing which has a 1/4 inch bore.
The problem is trying to match a 7/16 inch shaft with a 1/4 inch bore.
Does anybody have a seviceable one for sale or know where I could buy one or a modern equivalent?
I am also looking for Flat Head Machine screws with 82 degree countersink 1/4 X 1 1/8 and 1/4 X 1 3/8 All the usual sources do not stock them or the rod ends these days.
Thank you for any info.
Frank Cox
[Non-text portions of this message have been removed]
To unsubscribe from this group, send an email to:
fairchildclub-unsubscribe@yahoogroups.com
Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
[Non-text portions of this message have been removed]
'
Re: F24 elevator control Rod End
Posted: Sun Jun 09, 2002 7:56 pm
by ranger440c5
'John,
I may have the need for this rod end also, any others available?
Price? Thank you.
--- In fairchildclub@y..., "JOHN" wrote:
> Frank
> I have some control rod ends that might work for you. Give me a few
days and I will dig the box out and check for you. If I do you can
have it just pay the postage.
> John
'
Re: F24 elevator control Rod End
Posted: Wed Jun 19, 2002 8:52 pm
by JOHN
'So far all I have found is female or the rivit type
john
----- Original Message -----
From: F.J. & D.A.Cox
To:
fairchildclub@yahoogroups.com
Cc:
JSTreat360@aol.com ;
wbaf1595@att.net ; Tracy's mail
Sent: Wednesday, June 05, 2002 3:08 PM
Subject: [fairchildclub] F24 elevator control Rod End
Folks,
My rear elevator control 'Rod End' has been condemned.
It is 7/16 inch male thread with a 3/4 inch ring and a Fafnir S1K-5 Bearing which has a 1/4 inch bore.
The problem is trying to match a 7/16 inch shaft with a 1/4 inch bore.
Does anybody have a seviceable one for sale or know where I could buy one or a modern equivalent?
I am also looking for Flat Head Machine screws with 82 degree countersink 1/4 X 1 1/8 and 1/4 X 1 3/8 All the usual sources do not stock them or the rod ends these days.
Thank you for any info.
Frank Cox
[Non-text portions of this message have been removed]
To unsubscribe from this group, send an email to:
fairchildclub-unsubscribe@yahoogroups.com
Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
[Non-text portions of this message have been removed]
'
Re: F24 elevator control Rod End
Posted: Thu Jun 20, 2002 3:25 pm
by F.J. & D.A.Cox
'Many thanks for your efforts
Frank
----- Original Message -----
From: "JOHN"
To:
Sent: Thursday, June 20, 2002 3:50 AM
Subject: Re: [fairchildclub] F24 elevator control Rod End
> So far all I have found is female or the rivit type
> john
> ----- Original Message -----
> From: F.J. & D.A.Cox
> To:
fairchildclub@yahoogroups.com
> Cc:
JSTreat360@aol.com ;
wbaf1595@att.net ; Tracy's mail
> Sent: Wednesday, June 05, 2002 3:08 PM
> Subject: [fairchildclub] F24 elevator control Rod End
>
>
> Folks,
>
> My rear elevator control 'Rod End' has been condemned.
>
> It is 7/16 inch male thread with a 3/4 inch ring and a Fafnir S1K-5
Bearing which has a 1/4 inch bore.
>
> The problem is trying to match a 7/16 inch shaft with a 1/4 inch bore.
>
> Does anybody have a seviceable one for sale or know where I could buy
one or a modern equivalent?
>
> I am also looking for Flat Head Machine screws with 82 degree
countersink 1/4 X 1 1/8 and 1/4 X 1 3/8 All the usual sources do not stock
them or the rod ends these days.
>
> Thank you for any info.
>
> Frank Cox
>
>
> [Non-text portions of this message have been removed]
>
>
> To unsubscribe from this group, send an email to:
>
fairchildclub-unsubscribe@yahoogroups.com
>
>
>
> Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.
>
>
> [Non-text portions of this message have been removed]
>
>
>
> To unsubscribe from this group, send an email to:
>
fairchildclub-unsubscribe@yahoogroups.com
>
>
>
> Your use of Yahoo! Groups is subject to
http://docs.yahoo.com/info/terms/
>
>
>
'